Unifi snmp not working

Ubiquiti Controller forgotten password and unable to login! I am however surprised that it went through in the first place. If anyone out there know exactly why this happens please let me know in the comments below.

This amazing program will allow you to access the configuration files of the UniFi Controller. Not only does it allow you to access the files but it also lets you to edit the config files. An older version may be harder to find now so I am adding a direct link to the download below.

All credit goes to Robomongo developers, you may visit them at Robo 3T. Robomongo Download: robomongo Please make sure that you install the Robomongo software on the same computer UniFi Controller is running. Running it on a remote PC will not let you authenticate to the UniFi database. Once you have the program installed and running, please continue to step two.

Your password will be the longest line there in its encrypted form. Now we want to replace this password with another encrypted password, for that continue to step three. We will head over to Quickhash and download the program to generate a new encrypted password to be used with our UniFi controller. Alternatively, you may also use the pre-created password that I have below and reset it to your own once logged in. Password: ubuntu You should now be able to successfully sign in to the UniFi Controller.

I would also restart the controller if it is already running just to double-check it is working properly. If anyone has any idea why this issue occurs in the first place, I would appreciate it if you can shed some light on this problem in a comment below.

I hope this article was helpful for you in resolving the UniFi forgotten password issue. O is also my passion. If you are interested in my services, you may hire me to do content writing, content marketing or other S.As long as there is no brand pre If you want liberty, do not buy Ubiquiti.

Barrier Breaker Configurations then can be changed right away using LuCi.

unifi snmp not working

Later 3. If brick reset device with sec-press way with connected lan-cable - after it tftp start work. If you have already installed OpenWrt and like to reflash for e. Very helpful in case your upgrade went wrong or your AP is not responding anymore. A male-strip is on board to connect your TTL capable serial converter. Serial connection parameters:8N1. This will give you a steady green when the ethernet is up and a light blink during wireless activity.

This is a working standalone router setup, working as of The old version used a trick with bridging a nonexistent interface eth1 for no real reason, and it didn't work for me. Instead, I just set the wlan0 interface to be the lan network and everything worked perfectly. This is a working configuration that should be default, in easily pasteable form:.

The UniFi has only the single ethernet port, so much of the OpenWrt documentation is a little confusing. Clearly the Unifi doesn't have the wired LAN switch. After flashing I found r worked while the X subnet, running on the ethernet port. After changing the password and exiting, I had to wait a while 60 secs? That was strange because I thought I'd lost networking … I think that is due to a long-running first time ssh key generation.

Even so, each ssh in takes a long time to respond something about recent versions of dropbear taking a long time to setup a session key. Once ssh'd into the box I followed these steps: 1. Enable wireless, using commands at top of the UCI wireless config page.This guide covers the configuration of network devices in order to integrate them with PacketFence in VLAN enforcement. Covers API, captive portal customization, application code customizations and instructions for supporting new equipment.

There is no need to follow the instructions in this guide if you plan on deploying in inline enforcement, except RADIUS inline. Enabling RADIUS accounting on your network devices will increase significantly your database size and can cause performance issues. You should be aware of this and use accounting only if you really need it. PacketFence supports a whole lot of different wireless and wired network equipment from various vendors running different versions.

Throughout this configuration example we use the following assumptions for our network infrastructure:. If your management authentication on your switch is default, applying the configuration above will have your authentication switch to a RADIUS based one with PacketFence as the authentication server.

It is almost certain that you do not want that! Below, we will just create a local password for vty accesses telnet and nothing on the console. In order to avoid locking yourself out, make sure to verify your configuration! You now need to configure a user profile equivalent of a role that will determine which VLAN is assigned to the device.

In this case the profile names are 'unreg', 'employee' and 'guest'. First configure the user profile for voice. In this example it is only isolating it on another VLAN but any user profile attributes can be added to the profile.

unifi snmp not working

You now need to configure an edge profile equivalent of a role that will determine which VLAN is assigned to the device. Next, configure the switch in PacketFence. You will need to create an edge template and apply it on the ports you want to do authentication on. First configure the edge profile for voice. In this example it is only isolating it on another VLAN but any edge profile attributes can be added to the profile. So Avaya switches are, in effect, re-branded Nortels. See Nortel section of this document for configuration instructions.

Where xx and yy represent the range of ports where you want PacketFence enforcement. You also need to make sure that lldp or cdp notification is configured on all ports that will handle VoIP. Depending of the switch model, we recommend the use of the most secure and reliable feature first. In other words, you should consider the following order:. Those switches are now supported using So on setup that needs to handle VoIP with this switch, go with a Make sure that you have a local account, because enabling I've been trying unsuccessfully the past few months to get a few Ubiquiti Unifi AP-Pro s connected to Spiceworks, but I've not found a way to connect.

Yes, I have tried connecting through our stored SSH credentials and that did not work to connect any of them. It's odd to me since it doesn't need to connect using SSH. The AP-Pro isn't even getting scanned.

The IP address it has is being taken up by a manually managed printer that must have gotten set up on this network and gotten scanned before being sent out to one of our regional offices. So it can be seen. It only uses SSH for configuration backup. It doesn't actually read any of the data via SSH for network devices. The SSH Auth failed message you're seeing is probably due to the config backup script failing.

We can take a look at that, but I don't know if the Ubiquiti devices are something we can backup. Until we get the processes split which we're working onyou may be stuck with that. As for the device that has a manual device taking up it's IP address, you'll want to delete the printer from inventory. I had just finished changing a slew of proxyAddress values in adsi.

If you guys wouldn't mind taking a look at the backup script issue, that would be fantastic, especially if there are others that might be running into the same issue. Also, good to know on why the failed message showing up.

No worries bud! I'll shoot you an email with some instructions on getting your logs in. Keep an eye out for an email from support spiceworks.

When SNMP is not working — a troubleshooting guide

On the IP issue, it looks as though once I remove one inactive device, another regional device will take its place, rather than the active device with the assigned IP. Talked to my supervisor, and that may be an issue on our part, and the way that we have our networks set up locally and regionally.

To continue this discussion, please ask a new question. Get answers from your peers along with millions of IT pros who visit Spiceworks. I'm out of ways to troubleshoot, and would appreciate any insight you might offer. Is this a Spiceworks, Ubquiti, or network issue? Edited Apr 13, at UTC.You can ssh to your device, using the same credentials you use on your Unifi controller. If you connect via the serial port, you may have to play around with the baud rate.

I suggest you keep increasing it until it works. From my MacBook, this works for me:. The US had lost contact with the controller. I connected via the serial console and entered this command:. Checking the controller, the device was connected. From my reading, that will do way when I reprovision the switch, which I am about to do in order to change the management IP address.

You must be logged in to post a comment. Why hope? Unifi switches are designed to be managed via the webgui i. Now, what do I telnet to? The changes may break controller settings and only be effective until reboot.

What to do next? Any unsaved changes are lost. Network UBNT network? I changed the IP address Up IP Address Enabled IPv6 Prefix is None Configured IPv6 Protocol I connected via the serial console and entered this command: US. After provisioning completed which about a minuteinfo showed: US. Management interfaces will not be available during this time.

Are you sure you want to save? Configuration Saved! Hope this helps. December 19, at pm. Log in to Reply.AggrInt1 is connected to a FortiGate that also have an aggregated interface. All VLANs are set as corporate. Can someone please confirm and explain? Wired only "clients" for VLAN3 will be received by the switch. If true, then how? Link led indicators are active on both ports of each aggregated interface in every device. The IP Even though, I can ping all devices on the Again, I know that all others aggregated interfaces are working because I can ping everything from my computer except the FortiGate.

Not only that but on the HP switch I issued the command: display link-aggregation summary. On the Cisco switch I use the command: show interface port-channel 1 and on the Unifi switch the commands: telnet Everything seems to be in order.

On the Unifi switch the mac address of the switches and the FortiGate are listed. Here is an article I used in order to create switch port profiles. So I have a switch port profile that has my native network for network management then tagged vlans for Guest, IoT, and Testing networks.

unifi snmp not working

Hope this helps! It just looks like your switch is not tagging the traffic for VLAN5 and forwarding it untagged? Ubiquiti documentation is notorious for being lacking.

Monitor Unifi AP's

It's one of the biggest gripes and lack of proper support from them. That's why their devices are inexpensive I suppose. There is a trade-off somewhere.

It's only required if you want them to find the controller automatically. At that point the unifi DNS records isn't needed. With the record it simplifies life as you can just power it up and it'll show up automatically pending adoption. If you can't get to the controller's web GUI from anywhere else, that's a firewall issue. Either your Sophos firewall or the one built into the OS the controller runs on. I breezed past this post once a day ago when I didn't have enough coffee.

Edilcs messaged me to take a look. I don't see link aggregations stating what ports are together in the ubiquity configs. I just see the LAG interface definitions but not what ports are participating in each. I've only done LAGs on Summit Extremes, you don't configure anything on the non-master group-member ports, they get the same vlans and other settings as the master.

Initial Configuration Unifi Controller and Access Points │ English Version

A lot of high end firewalls don't allow ping by default, and often don't allow much of anything by default except go out to the internet and get back data.When directly connected there is no power to any camera. When an POE injector is used there is a connection and data is passed.

Looking at the logs it does not show that the units are not detected at all. Changed the power settings at the port level with no success. Does anyone have any ideas? Go to Solution. I really don't think that changing any settings on the switch is going to power those cameras. View solution in original post. If its not working with other devices either may be a firmware issue but if it is, it could be a poe type negotiation issue between the sf and the cameras.

Thanks for responding with information. I then used the same cable and plugged in a camera that had not been installed yet and got no response. Well there you go The units come with injectors so it's off to get power strips to plug into the UPS and a bunch of Ethernet cables.

Thanks for the help on this. Thanks for the links of information. I check this type which is a video dome and it has passive power needs between 12V and 24V, with a max watt of 4W. I modified the switch ports to put out no more than mWv 4W but still no draw. The customer's Avaya phones seem to function fine when plugged in without their injectors. Buy or Renew. Find A Community. We're here for you! Turn on suggestions. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for. Search instead for. Did you mean:. Victor Smith. Labels: Other Switching. I have this problem too. Accepted Solutions. Rising star. See my reply above. You will need to either: A Upgrade the the Pro Cam which seems to use 48v and should work with the Cisco switches B Use a Ubiquiti Edge Switch as they support 24v PoE C Use a power injector I really don't think that changing any settings on the switch is going to power those cameras. Mark Malone.

VIP Mentor. Hi do the cameras support the Thanks for responding with. I have had issues with. I have had issues with Ubiquiti stuff and Cisco PoE before.


thoughts on “Unifi snmp not working”

Leave a Reply

Your email address will not be published. Required fields are marked *